Ok, so here's the deal. In making my own braided feed line for the 05 BEW Golf I recently picked up, I had a debacle with Summit shipping me twice the correct length but wrong size of hose. I finally ended up finally getting the correct size hose for my personal car, but I ended up with several feet extra (originally wanted 3 feet, ended up with 10 feet).
So rather than let the extra hose go to waste, I thought I'd offer this. A PTFE -4 Braided Oil Feed with a 90° and straight fitting, block and turbo adapters with washers, for $50 shipped. That is fully assembled ready to go.
Here's what's in it:
90° -4 PTFE Hose End -- $11
Straight -4 PTFE Hose End -- $5
~29" -4 PTFE Hose (end to end before assembly) -- $10
10mm x 1.0 to -4an Adapter -- $5
12mm x 1.5 to -4an Adapter -- $5
Cost of parts to DIY would be $36 plus $10 Handling from Summit (comparing local and on line they were the best deal for me as usual). So $46 plus doing it yourself which if you haven't done PTFE before, is a bit of a pain.
I guarantee these hoses. You have an issue, I will take care of it. For references since I'm not a big name around here, I'm an admin and co-owner of LTxTech.com, upstanding member and former sponsor of the Corvette Forum, and run a small biz doing mainly brake line lock kits for Corvette's and braided fuel lines for LT1 Firebirds and Camaro's under Fastbirdperf.com. Been doing this for 9 years now with no issues. Point with all that is that I stand behind anything I sell.
And, as I mentioned prior, I have hose left over to do two more on top of this one that's already done, then I won't do it again because the cost would have to go up. I'm not looking to be a full time vendor with this, just looking to make use of the extra hose I had left over so it doesn't go to waste and give 1 to 3 people max (which will be all the hose I have at the 3rd person) a good deal on a braided oil feed hose.
Mods, if you have issue with anything, shoot me a PM and let me know what you want corrected.
So rather than let the extra hose go to waste, I thought I'd offer this. A PTFE -4 Braided Oil Feed with a 90° and straight fitting, block and turbo adapters with washers, for $50 shipped. That is fully assembled ready to go.
Here's what's in it:
90° -4 PTFE Hose End -- $11
Straight -4 PTFE Hose End -- $5
~29" -4 PTFE Hose (end to end before assembly) -- $10
10mm x 1.0 to -4an Adapter -- $5
12mm x 1.5 to -4an Adapter -- $5
Cost of parts to DIY would be $36 plus $10 Handling from Summit (comparing local and on line they were the best deal for me as usual). So $46 plus doing it yourself which if you haven't done PTFE before, is a bit of a pain.
I guarantee these hoses. You have an issue, I will take care of it. For references since I'm not a big name around here, I'm an admin and co-owner of LTxTech.com, upstanding member and former sponsor of the Corvette Forum, and run a small biz doing mainly brake line lock kits for Corvette's and braided fuel lines for LT1 Firebirds and Camaro's under Fastbirdperf.com. Been doing this for 9 years now with no issues. Point with all that is that I stand behind anything I sell.
And, as I mentioned prior, I have hose left over to do two more on top of this one that's already done, then I won't do it again because the cost would have to go up. I'm not looking to be a full time vendor with this, just looking to make use of the extra hose I had left over so it doesn't go to waste and give 1 to 3 people max (which will be all the hose I have at the 3rd person) a good deal on a braided oil feed hose.
Mods, if you have issue with anything, shoot me a PM and let me know what you want corrected.
FS: ALH/BEW Braided Oil Feed Line
0 commentaires:
Enregistrer un commentaire